Specifications + Dimensions

M1308A12 Specifications:
60 Hz @ 1800 rpm435 kW
50 Hz @ 1500 rpm400 kW
Cylinders:V-8
Bore:5.12 in (130 mm)
Stroke:6.1 in (154 mm)
Displacement:1001 cid (16.4 ltr)
Fuel System:PDE/S6 EMS
Aspiration:Turbo and Aftercooled
Length:106 in (2683 mm)
Length with Enclosure:Consult Factory
Width:48.2 in (1224 mm)
Width with Enclosure:Consult Factory
Height:51.7 in (1314 mm)
Height with Enclosure:Consult Factory
Weight:Consult Factory
Weight with Enclosure:Consult Factory
M1308A22 Specifications:
60 Hz @ 1800 rpm475 kW
50 Hz @ 1500 rpm420 kW
Cylinders:V-8
Bore:5.12 in (130 mm)
Stroke:6.1 in (154 mm)
Displacement:1001 cid (16.4 ltr)
Fuel System:PDE/S6 EMS
Aspiration:Turbo and Aftercooled
Length:106 in (2683 mm)
Length with Enclosure:Consult Factory
Width:48.2 in (1224 mm)
Width with Enclosure:Consult Factory
Height:51.7 in (1314 mm)
Height with Enclosure:Consult Factory
Weight:7607 lbs (3450 kg)
Weight with Enclosure:Consult Factory
M1308A32 Specifications:
60 Hz @ 1800 rpm514 kW
50 Hz @ 1500 rpm450 kW
Cylinders:V-8
Bore:5.12 in (130 mm)
Stroke:6.1 in (154 mm)
Displacement:1001 cid (16.4 ltr)
Fuel System:PDE/S6 EMS
Aspiration:Turbo and Aftercooled
Length:106 in (2683 mm)
Length with Enclosure:Consult Factory
Width:48.2 in (1224 mm)
Width with Enclosure:Consult Factory
Height:51.7 in (1314 mm)
Height with Enclosure:Consult Factory
Weight:Consult Factory
Weight with Enclosure:Consult Factory
M1308A42 Specifications:
60 Hz @ 1800 rpm545 kW
50 Hz @ 1500 rpm475 kW
Cylinders:V-8
Bore:5.12 in (130 mm)
Stroke:6.1 in (154 mm)
Displacement:1001 cid (16.4 ltr)
Fuel System:PDE/S6 EMS
Aspiration:Turbo and Aftercooled
Length:106 in (2683 mm)
Length with Enclosure:Consult Factory
Width:48.2 in (1224 mm)
Width with Enclosure:Consult Factory
Height:51.7 in (1314 mm)
Height with Enclosure:Consult Factory
Weight:Consult Factory
Weight with Enclosure:Consult Factory

Notes

  1. Prime kW ratings for 3Ø at 0.8 power factor. Consult factory for deration factors.
  2. Net flywheel hp rating for fully equipped engine at rated speed under SAE J816b.
  3. Based on prime kW rating at 1800 and 1500 RPM. Fuel rate may vary depending on operating conditions.
  4. Data for units with hydrolastic mounts, heat exchanger cooling and 3 phase generator ends. Dimensions and weight are affected by optional equipment, AC output, phase, exhaust and cooling configuration.
  5. Consult factory for data on enclosures for sets with InSep.

Dimensions and weights are subject to change without notice, they are not intended for installations.

Contact a factory representative for the current installation data

Features + Benefits

  • Vee-eight cylinder, four cycle, liquid cooled, overhead valve, marine diesels based on heavy-duty industrial engine blocks.
  • Balanced, alloy steel crankshaft with hardened and polished bearing surfaces
  • High position alloy steel camshaft and pistons.
  • Three ring aluminum alloy pistons with Ni-Resist insert for the top ring. Keystone piston ring reduces carbon buildup under light loads.
  • Two gear-driven, counter-rotating balancing shafts for smooth operation.
  • Eight groove poly-vee drive belt powers the alternator and freshwater pump.
  • Replaceable, strength-optimized wet cylinder liners for long life and low rebuild costs.
  • Electronically controlled fuel injection systems for low exhaust emissions and superior fuel economy.
  • High torque at low revolution. (1800 or 1500 rpm)
  • Ring clamp fuel filter with air bleed and drain.
  • Diaphragm-type, mechanically driven fuel transfer pump with manual priming lever.
  • Flexible fuel lines routed to fuel manifold on base frame for easy installation of vessel’s hard piping.
  • 500 hour oil change interval when fuel and oil requirements are met.
  • Positive displacement gear-type oil pump.
  • Full flow, spin-on oil filter.
  • Centrifugal oil cleaner reduces piston crown temperature for longer life.
  • Freshwater, plate-type, full flow oil cooler reduces heat and thermal breakdown of lube oil.
  • Large capacity oil pan.
  • Floating, cast aluminum, rocker cover traps valve noise and is a closed loop crankcase vent.
  • Lube oil drain for easy changes.
  • Closed crankcase ventilation.
  • Dry air filter silences intake noise.
  • After-cooler with aircraft quality, 70/30 cupro-nickel, two pass element.
  • Twin, isolated turbocharged for increased output. Fresh-water cooled turbine housings for safety
  • Freshwater cooling system with twin thermostats for quicker warm-ups.
  • Duel heat exchanger with expansion tanks. Gear driven, flexible impeller seawater pump. Easy to clean, tube-type cupro-nickel heat exchanger.
  • Cast iron expansion tank with brass filler neck. Cast-iron exhaust manifold has double pass freshwater flow for even temperature control, fast warm-up and no hot spots.
  • Zinc anode electrolysis protection.
  • SAE J1939 data stream available through a CAN bus plug for optional engine monitor.
  • Isolated ground 24 VDC system with circuit breaker, starter motor and battery charging alternator with regulator.
  • Standard ComAp InteliGen NT marine panel for switchgear mounting displays engine and AC data. Upgradable with enclosure, synchronizing and paralleling capability.
  • Low oil pressure and high coolant temperature safety shutdown system.
  • Direct coupled, single bearing, 12 lead, reconnectable AC generator. Maintenance free brushless design.
  • Generators meet or exceed class society standards. All have class H insulation, accessible diodes, oversized ball bearings, marine grade shafts and conservative 95°/50° heat rise ratings.
  • Engines and generators are torsionally matched for long life.
  • Automatic voltage regulator gives fast response to electrical load changes. Voltage is regulated to ±0.5% (one half of one percent) over the entire range from no load to full load.
  • Isochronous electronic governor for 0% AC frequency droop.
  • PMG (permanent magnet generator) to power AVR for 300% short circuit capability for classed vessels.
  • Standard hydrolastic mounts isolate 98% of hull vibration.
  • Welded steel base frame with drip pan. Easy to mount and keep clean.
  • Belt guard protects operator even on sets in sound enclosures.
  • Sparkling white IMRON® polyurethane paint for protection and visibility.
  • Operator’s and parts manuals.
  • Meets or exceeds US EPA Tier III emission standards.
  • IMO compliant.
  • Consult factory for additional details.
© Northern Lights, Inc. 2017